Mifarelavori

Develop schematics, PCB and firmware for a compact NFC reader. The suggested RFID controller is PN7160. Microcontroller - STM32 0) Two boards - antenna and the main board. The antenna diameter is 15mm with a hole in the center 4-5mm. The main board is 14mm in width and length is 35mm or less. 1) The reader must read and write password-protected memory blocks in Mifare Classic cards. 2) The reader keeps the password for the RFID cards as a hard-coded constant. 3) The reader has an 4-byte reader ID stored in its EEPROM memory. 4) The RGB LED on the edge of the main board, whose location matches the hole in the antenna. RGB LEDs are connected to the PWM pins of the controller. 5) A waterproof (if possible) speaker must be on the opposite edge of the main board, closer to one side to l...

I need a compact and efficient RFID decoding device that can effectively handle access control duties. We have multiple RFID 1k cards which are encrypted. We want to decrypt the card and should be able to edit the data in it Key Requirements: - **RFID Support**: The device should be able to work seamlessly with Low Frequency (LF) RFID tags. Such as mifare 1k. RFID 1k card - **Wi-Fi Connectivity**: if required it should have Wi-Fi capabilities to enable remote access and data management. Ideal Freelancer: - Proficient in RFID technology. - Experienced with access control systems. - Skilled in hardware development and connectivity. - Ability to create a compact and user-friendly device.

I am looking for someone to develop an extended range RFID antenna for ISO 14443 A protocol that will interface to a Flipper Zero. Antenna and Flipper needs to operate at least upto 50cm but ideally 100cm. Antenna may need an additional driver stages and a battery pack to enhance the range. Anybody who sends me UHF RFID equipment or suggests it will be ignored....someone to develop an extended range RFID antenna for ISO 14443 A protocol that will interface to a Flipper Zero. Antenna and Flipper needs to operate at least upto 50cm but ideally 100cm. Antenna may need an additional driver stages and a battery pack to enhance the range. Anybody who sends me UHF RFID equipment or suggests it will be ignored. ISO 14443 A operates on 13.56 MHz (HF) looking for a Mifare Ultralite solution a...

I am looking for app developers who can incorporate the ability to both read and write to a Mifare Desfire EV1 card. In detail, here are the key requirements: 1. Android App: - Design and build an Android app that can interact with the Mifare Desfire EV1 card - Capable of reading and writing Authentication data to and from the card 2. IOS App: - Create an IOS app that can read this Authentication data from the same card Our main goal is to use this Authentication data for user login/authentication for internal use. The successful freelancer should have skills and experience in Android development, IOS development, and working with Mifare Desfire EV1 cards, preferably with Taplinx. Knowledge in data security is a must. Ensuring privacy and security of the data is ...

I am looking to develop a specialized program for the PN5180 reader with a focus on reading ID card data. This is a personal project aiming at making ID card management more efficient. The program just need joint with our team and help to code for read data from reade with scan time below 3 second. Reading the mifare ISO 14443 card, using mrz information and APDU command for selecting, reading data Ideal skills and experiences include: - Proficiency in programming the Esp32 platform - Experience with PN5180 reader - A good understanding of ID card reading procedures and requirements. Please ensure to provide relevant examples of your past projects.

CREAR UNA BIBLIOTECA ENCRIPTACION AES PARA TARJETA MIFARE PLUS PARA ARDUINO ESP32

I am looking for app developers who can incorporate the ability to both read and write to a Mifare Desfire EV1 card. In detail, here are the key requirements: 1. Android App: - Design and build an Android app that can interact with the Mifare Desfire EV1 card - Capable of reading and writing Authentication data to and from the card 2. IOS App: - Create an IOS app that can read this Authentication data from the same card Our main goal is to use this Authentication data for user login/authentication for internal use. The successful freelancer should have skills and experience in Android development, IOS development, and working with Mifare Desfire EV1 cards, preferably with Taplinx. Knowledge in data security is a must. Ensuring privacy and security of th...

Necesitamos un programa para arduino mega o nano, con lector rfid-rc522 para tarjetas o tags mifare que modularmente nos permita: 1. Almacenar en algun sector de la tarjeta los siguientes datos: Fecha, vl1:0,1,2,3, vl2:0,1, vl3: 0 a 1000000 (saldo), protegida con un keya,keyb diferente al deffaul. 2. La idea es leer los datos y visualizarlos en variables para mostrarlos en monitor serie. 3. Cambiar datos: actualizarlos, puede ser en tarjeta nueva o cambiar los existentes.

Hi, We're building a contactless payments application. Need a simple application that will provide an ID + some randomness. My partner will read it with their terminals and send the value to me via an API. Thinking of using MIFARE DESFire Light or MIFARE DESFire EV3. Need help setting up the cards and writing documentation to my partner for integration. Need to execute this in 2 weeks max. Thanks! Alejandro

...projects is absolutely essential. We have existing hardware and software systems that the RFID custom app needs to integrate with. Therefore, we require a developer who has experience in integrating RFID technology with existing systems. Skills and Experience Required - Strong knowledge and experience in RFID technology and its applications - Closed loop payment systems. - Card / token security - Mifare Desfire - Full tech stack. - Proficiency in app development for both Android and iOS platforms - Experience in integrating RFID technology with existing hardware and software systems - Familiarity with inventory management, access control, and asset tracking concepts - Attention to detail and ability to create user-friendly interfaces If you have the skills and experience re...

I need to develop a compact reader for Mifare Classic or Mifare Ultralight. The board width is 15mm, antenna diameter is 15mm. The device should read password-protected areas and send them to the host via RS485 interface. I need schematics, a PCB, and a working prototype. 3-4 weeks deadline. Please see the attached description.

Bonjour je souhaiterai des proposition de design pour carte de chambre d'hotel c'est carte permettent d'ouvrir la chambre elle doivent comporter le logo et le texte suivant dessus Le design doit être fait au format portrait ce sont des carte sans contact de type mifare et non des carte a piste magnetique c'est un format standar CR80 85.6 × 53.98 mm 8 Place de la Gare 14000 Caen, France 02 31 34 06 03

code allows you to emulate a mifare classic 1k card (serial number) that is used to open the doors that are equipped with a normal MIFARE Classic 1K reader

Actualmente estamos desarrollando sobre una app en flutter y necesitamos una persona que desarrolle la comunicación con las tarjetas NFC Mifare Classic 1k. Ya tenemos posibilidad de escribir y leer pero el requisito principal es que los datos almacenados en las tarjetas queden protegidas y solo puedan ser leídas y modificadas por nuestra aplicación.

Tenemos un proyecto para transporte público, hemos desarrollado una aplicación en Flutterflow, requerimos lo siguiente: - Crear un código para Arduino en C++, que permita leer y escribir bloques en tarjetas Mifare Desfire EV1 4K. Debe incluir la encriptación AES 128. - Debe tener comunicación Bluetooht y Micro USB para trabajar con Smartpone con Android y iOS - Hardware utilizar ESP32 + MCFR 522 o ESP32 + PN532 o Arduino Uno + MFCR522 + Bluetooth. - Escribir un codigo para la logica de la aplicacion en lenguaje .dart que esta desarrollada la app, tiene opciones para agregar lineas de codigo con opciones de custom code , action code, widget plugin. - En la aplicacion existen dos interfaces una para ver saldo y otra para recargar monto. - La inte...

Senior Native Android Developer (Kotlin) We have a mobile application running on an Android 7.1 POS device. The task of our application; It is to communicate with Vending Machine, to which it is connected, over MDB protocol, to read debit and other mifare cards contactless, contactless and magnetic and to receive payments through its APIs. We already have an existing application and it is integrated with VMC, it can make sales transactions and receive payments. If what we want to do - direct bank integration (AIDL app integration) - Reading Mifare cards contactless and collection from APIs according to UID value - Integrating new UX designs into the project - Integration with Kiosk via MQTT - Integration with USB - Log storage structure within the application - Stable and ...

Senior Native Android Developer (Kotlin) We have a mobile application running on an Android 7.1 POS device. The task of our application; It is to communicate with Vending Machine, to which it is connected, over MDB protocol, to read debit and other mifare cards contactless, contactless and magnetic and to receive payments through its APIs. We already have an existing application and it is integrated with VMC, it can make sales transactions and receive payments. If what we want to do - direct bank integration (AIDL app integration) - Reading Mifare cards contactless and collection from APIs according to UID value - Integrating new UX designs into the project - Integration with Kiosk via MQTT - Integration with USB - Log storage structure within the application - Stable and ...

Requiero un programa y libreria simple capaz de leer un tag mifare con un microcontrolador Pic, este debe estar escrito en codigo C para MPLAB X o CCS compiler, la comunicación debe ser I2C, el sensor es "RFID PN532 V3 NFC", el PIC es de la familia 16F por ejemplo "PIC16F628A". La finalidad es obtener la ID o codigo de una tarjeta Mifare.

Develop a prototype Dotnet Maui Android C# application running on a Samsung Galaxy Tab Active3 to connect a acr1255u-j1 RfId Reader with BLE connection. The app should be able to continuously read multiple Mifare Classic cards that are tapped on the RfId reader. The RfId reader should beep when reading a card and the card's uid should be output to the console as a 10 digit decimal number. A third party library can be used as long as there are no royalty fees or charges for the library. No Copyleft license libraries should be used. All source code should be in English and provided with no obfuscation and should be buildable in Visual Studio 2022. The manual for the acr1255u-j1 rfid reader is a pdf at Skills and Experience

Hello everyone, I am posting this project because I am looking for someone who would be able to bypass locked sector on my RFID ultralight card. I have an ACR122u reader/writer and a working kali linux distribution. Attached is a screenshot of the sectors unlocked

I need use phone allways in door entrance system. Need to find solution that mobile phone allways return same nfc value to mifare or nfc card reader

I need to create an Android/Apple APP that allow my customer to access to my gate not only by MIFARE CLASSIC TAG NFC but also with by Smartphone. By NFC Mifare Classic I read UID and check it on DB. So I want app where user insert UID and push Emulate and than my smartphone appear like mifare classic tag.

I need to create an Android/Apple APP that allow my customer to access to my gate not only by MIFARE CLASSIC TAG NFC but also with by Smartphone. By NFC Mifare Classic I read UID and check it on DB. So I want app where user insert UID and push Emulate and than my smartphone appear like mifare classic tag.

We are an Access Control manufacturer and we are looking for developers/freelancers/consultants that can help us build our new DESFire EV2 reader. Our hardware is based on ST MCU and we will connect it to an NXP SAM. We less need assistance in hardware design but more in understanding deeply the protocol and the way to use it, and also in defining the requirements for such a product.

Good afternoon JFreddy, We are working on a transit project and need to program some Mifare Desfire EV2 2K cards, the application also uses a SAM to provide new keys and encrypt some data. Are you familiar with programming these cards and would you like to provide some code to assist us in our development? Budget and cost can be discussed once we clafiy if you can or would like to assist thanks Dave

We require assistance and code (Delhpi or C) to assist us in a project that involves programming (key replacement and application creation) of Mifare Desfire EV2 2K cards. Details on exact requirements, level of involvement and projest cost would be discussed with canditates

Tasks: Developing a Flutter plugin for communication with MIFARE Ultralight C tags via NFC using the PAX A920 equipments. Allowing normal read/write raw bytes commands, setting up authentication parameters and authenticating to the tags before any read/ write/ ISO command. In summary: recreating the nfc_manager Flutter plugin, using solely the PAX A920 equipment and Mifare Ultralight C tags.

am looking for mifare and rfid card encoder FIRMWARE main boards and firmware pictures attached main chip is

Необходимо разработать миниатюрный микроконтроллер для чтения RFID карт в стандарте MIfare. Требования: Питание: 9-36 вольт. Защита от скачков напряжение до 70 вольт.(микро пульсации) Выход 1: Открытый коллектор- наличие карты. Выход 2: 1-wire в протоколе IBUTTON Исполнение антенны: Использование готовой индуктивной катушки. Светодиод подсветки наличия карты. Обязательное условие: Опыт проектирования, программирования, а так же опыт сопровождения производства и сборки микроконтроллера под заказ.

...Card + QR code reader, developed with NXP PN7150 IC, a QR Code reader module, ESP32 as the microcontroller, and some other peripherals. The PCB ,antenna tuning, code(micropython)is done in-house. The RFID card reader is used to read , ISO14443A ( MIFARE, Desfire, ) and ISO15693 Cards. Only CSN reading is done for now and no key or key management is implemented whatsoever. We are successfully reading the above cards. Now, we are facing a few problems in the functionality 1- The read distance is very low (only about 15 mm read distance for mifare, desfire and 45 mm for iso15693 cards, this should ideally be around 45 and 60 mm respectively.) 2- The read speed is a little bit less than optimal, the card has to be presented and held for a little less than 1 second, this sh...

Create three method on java for a android Studio app: -Topup Balance -Withdraw Balance -Balance check Note: Only people with DESFire card experiences.

Freelancer is required to write code in Java for programming MIFARE CARDS , NTAG216 Enabling counter ,locking memory Develop Application for Android ,windows and iOS Only experienced freelancer required .

Develop a demo SW to read tags DESfire EV1. The HW include a security element SE050 as reader and a host MCU.

Hi Alex.. we are looking for someone to help in Encoding Mifare Plus SE Card. Can you help and support us.

I need windows app for read & write NFC Mifare card with ACR112U reader/writer (). In details I need to load excel file and write data on card.

Need to write 1000 Mifare Classic cards with a ACR1252u writer. Existing program is fine too, need one that can let me specify which byte in which sector and block location I have to write.

Hi softtouchsystem, I noticed your profile and would like to offer you my project. We can discuss any details over chat. I need an android apps for NFC mifare desfire Ev1. We need 2 apps: 1 is writting apps, 1 is client apps. Writting apps: The apps can write database ID and secret key to desfire, then encrypt the database ID with secret key, and upload that encrypted ID to server through our api. Client apps: The apps can read database ID, and encrypt the ID using the secret key inside desfire. That encrypted ID will use to verify in our server through our api. The secret key should not be visible nor hackable. Please let me know the estimation.

Nous recherchons un développeur pour la partie mobile (android) d'un système privatif de paiement par carte NFC mifare Desfire.

Seeking honest, truthful, reliable, professional partners for this task. Need a cross platform mobile app (iOS, android, UWP) that will read/write/manage NFC, Mifare, 1D, 2D, QR, Data Matrix, BLE beacons, RFID (HF, UHF via external Hardware device) tags or impressions. The hardware transport shall be various Wi-fi, Bluetooth flavors that are supported in today's phones. You may list the flavors you will support or else we shall assume BT5, BLE all versions, classic Bluetooth. Please make a simple UI wireframe , a flowchart, submit & get approval before proceeding. We assume you have the suitable phone HW and environment for development. You may use the tags that are available with you or add the cost of each tag unit (please specify the approximate cost separately, if you l...

Seeking honest, truthful, reliable, professional partners for this task. Need a cross platform mobile app (iOS, android, UWP) that will read/write/manage NFC, Mifare, 1D, 2D, QR, Data Matrix, RFID (HF, UHF via external Hardware device) tags or impressions. The hardware transport shall be various Wi-fi, Bluetooth flavors that are supported in today's phones. You may list the flavors you will support or else we shall assume BT5, BLE all versions, classic Bluetooth. Please make a simple UI wireframe , a flowchart, submit & get approval before proceeding. Also let us know the language, IDE, OCR engine you shall use. Our preference flutter with Darknet or Tensorflow. Please suggest the RFID reader HW you shall like to use, we have several here, but like to see if you have any ...

Design Mifre Enocding system and advice on best method to protect the card Mifare Classic.

Job Position: iOS developer Job Spec: We are looking for an iOS developer to create a simple SDK and S...developer to create a simple SDK and Sample Application. This application will need to handle NFC Communication and Authentication between the iPhone and proprietary electronics hardware. This will also need to store keys in the iPhone Secure Element. This SDK and Sample application will be provided to our clients in order for them to build their own applications. The NFC communication scheme (MIFARE DESFire) and API have already been decided upon and implemented in an Android SDK. These are limited in scope, and would not need to be developed further. Qualifications: • Previews experience with NFC is preferred Additional Skills: • Android knowledge • ...

Scan and amend stored value in MIFARE Plus X card on a laptop or iphone.

We are looking for an iOS developer to create a simple SDK and Sample Application. This application will need to handle NFC Communication and Authentication between the iPhone and proprietary electronics hardware. This will also need to s...developer to create a simple SDK and Sample Application. This application will need to handle NFC Communication and Authentication between the iPhone and proprietary electronics hardware. This will also need to store keys in the iPhone Secure Element. This SDK and Sample application will be provided to our clients in order for them to build their own applications. The NFC communication scheme (MIFARE DESFire) and API have already been decided upon and implemented in an Android SDK. These are limited in scope, and would not need to be developed...

1.1. What is EPS Device? EPS Device is the electronic payment system which provides the methods of EMV contactless payment and QR code for passengers to pay the bus fare. Both methods support offline mode, which the transactions via the EPS Device will be completed at the speed comparable with Mifare S50 card. 1.2. Who should read this document? Technical Team, Business Development Team and Owner are encouraged to read through the following to understand the EPS Device and integration. This document will cover system overview, sequence diagram with API specification in details, we expect readers shall have a better understanding to complete the implementation of EPS integration. 1.3. Supported Payment Method The EPS Device should support the 3 kinds of EMV card and 6 kinds of QR cod...

Create a Flutter NFC Plug in that only reads the UID of the Tag and works in Android and IOS. It's doesn't have to be as complicated as but it does have to use the following Swift co...{String(format: "%.2hhx", $0)}.joined() print("UID Ross 29", UID) print() () } } The Plugin just has to return the UID of the card and not use any of the NDEF calls in Swift. It should behave like other flutter NFC plug ins but the NFC box has to disappear as soon as the mifare Identifier is found. Note - I am only going to respond to quotes less than $100 and you must have Flutter Plugin Experience and an iphone and Android and NFC cards for testing.

Hi. I'm running a cafe. I plan to have a system that controls prepaid items. Ie: customer buys 10pcs product A, 5pcs B, 20pcs C, but will only redeem them progressively. Each customer will be given a contactless card (nfc or mifare), each time an order is made, the card will be used to "pay/redeem" for items. Customers can check their credits at a checkpoint. The system can either be Android(smart phone), RaspberryPi, ESP32, Arduino based. Working offline. Hardwares that I have: Esp32 , esp8266 Rpi NFC reader, cards .Etc

i need to create or update NFC plugin to read mifare classic , with to :  note i have test below plugin using Flutter and it work for me

Android and IOS app for NFC-enabled phones to emulate mifare card. The app runs in the background so the user should only bring their phone closer to the reader. Emulates a tag with read write data, type mifare 1K. All data will be manageable from a server. The user can only install the app and give permissions. From the server you can turn the tag on and off, change the ID, read the data memory, and write to the data memory. The app will have id of the phone on which it is installed, so that the tag data cannot be copied to any other phone.

...a mobile app for Android and iOS, developed in Embarcadero Delphi 10.4.1 Firemonkey framework. Delphi 10.4.1. No other Android, iOS solution is acceptable. Requirement: - Ability to send a message from backend server to a mobile as push notification - Access Near-field communication (NFC) [MiFare Card] to read MIFARE cards - Access camera (Front to take user photo) - Access camera (Rear for QR Code scanning) - The app should logs the Latitude & Longitude (high accuracy) when user Tag on the MiFARE card, click check-in button or scan the QR Code. Some time need to take picture. - The application should monitor (start Location Sensor background service even if application is close) and log the Latitude & Longitude (high accuracy) when user enter or leav...