Orcad designlavori

I need to know what software generate such schematics. These are samples from ICOM, Kenwood and YAESU transceivers but similar graphical schematics are also popular if you search internet. Note that OrCAD, Eagle and other well known electronic CAD's does not output such designs (the components are drawn different, etc). ## Deliverables 1) Complete and fully-functional working program(s) in executable form as well as complete source code of all work done. 2) Deliverables must be in ready-to-run condition, as follows (depending on the nature of the deliverables): a) For web sites or other server-side deliverables intended to only ever exist in one place in the Buyer's environment--Deliverables must be installed by the Seller in ready-to-run condition in the Buy...

Layout of approximately 35 parts PCB board in Orcad or any other Gerber compatible software. The entire layout consists of 5 surface mounted ICs, 1 OSC, 2 ethernet jacks, a 7805 regulator, an interface connector, and rest passive componets. Our current design consists of 3 DIP ICs with 8 bit I/O port. The new design will expand this to 16 bit I/O. The designer must be familiar with PCB design.

im looking for someone to help me in the schematic design of a multipurpose pcb based on a microprocessor, for development board some of the functions that the PCB must include are 1)SDRAM memory , 3)USB port 2.0 3)touchscreen LCD 4)Bluetooth,5) Molex connectors 6)802.11/a/g The unit would have a small embedded linux kernal and GUI web interface in cross platform language( , JAVA, or FLASH) Remember, is just for the design concept, not hardware to deliver ## Deliverables All deliverables will be considered "work made for hire" under U.S. Copyright law. Buyer will receive exclusive and complete copyrights to all work purchased. (No GPL, GNU, 3rd party components, etc. unless all copyright ramifications are explained AND AGREED TO by the buyer on the site per the c...

I have an orcad file design (.dsn) and i want to make a layout of it but with the following conditions 1-it must be one layer 2-All components packages are DIP not surface mount note that some components may require that you look for its alternative as it hasn't a DIP package Make sure that you can make it one layer before bidding ## Deliverables 1-An orcad layout file 2-A list of the components that you have changed ## Platform orcad

We require a developer for a simple electronics schematic and PCB. Most of the information on components to use will be provided to you including all data sheets. You will have to use your electronics savvy and interface these components and supporting resistors and capacitors although most of the data sheets have examples. Please note that we're an electronics c...the platform(s) specified in this bid request. 3) All deliverables will be considered "work made for hire" under U.S. Copyright law. Buyer will receive exclusive and complete copyrights to all work purchased. (No GPL, GNU, 3rd party components, etc. unless all copyright ramifications are explained AND AGREED TO by the buyer on the site per the coder's Seller Legal Agreement). ## Platform * ...

Design hardware and firmware for a PIC18F microcontroller to do a similar function to the DRO-350 device shown here: http://www.shumatech.com. It must interface with Chinese-style digital caliper output OR quadrature encodeer input. The hardware can be vastly simplified by directly driving special low-current LED displays such as these ones: , requiring only digit drivers. The quadrature and caliper input ISRs should be written in well-documented assembler, and the rest should be written in C, using built in math functions such as the trig functions for bolt hole calculations. All firmware must be written from scratch or taken from documented and agreed-to public domain sources. Circuit design also to be original (not copied). I can provide time-limited

We require a developer with demonstrated skill in electronics, schematic design and pcb design to assist us with the design of our hardware project. The developer would need to be familliar with Texas Instruments DSP devices (essentially BGA devices), ADC/DAC (SOIC/TQFP), Flash (NAND) and SRAM as well as other SMD devices. We would like the developer to be prepared to develop the following: 1 X Schematic Diagram of our hardware project 1 X PCB layout of a prototype board allowing us to use sockets for the DSP's and other expensive parts 1 X Final PCB to be designed for manufacture. As part of your deliverables we would require 1) Advise on correct selection of components, ADC, DAC, Flash, SRAM etc 2) Assistance with rudementary electronics queries. We have as much...

The Projekts is requested from a german engineer office. We setup the Scematics (prefear PADS, OrCad, Eagle) with our Costumers. We planing to transfer to Freelancer for Routing manually. We looking in far east aerea (India, China, Thai, Malaysia, Indonesia...). We want to setup longterm bussines relation. Please contact us, when experiance in high complex design of PCB-Design (like PC-Mainboards complexity, BGA, 8 Layers...) No Autorouters offers pls. Meby workgroups for 24hrs-shift-work wellcome for faster results (extra bonus) Also contact use to get some testprojekts for show ability an complexity of or requested jobs.

_AC input:_ 100V ~ 240V AC _**F...transmission) _Small_ compact Anntenas _Remote_ Control to switch jammer ON/OFF _Dimensions_: 100mm(W) * 100mm(L) * 30mm(H) **_Installation_**: Need to have the casing designed for project with easy wall or ceiling mounting facility Need to know if u previosly worked on similar project. Thanks ## Deliverables 1) Provide Desihn Schematic 2) Provide Design Layout in ORCAD format 3) Design Documentation 4) Parts lists and description 5) Exclusive and complete copyrights to all work purchased. (No GPL, GNU, 3rd party components, etc. unless all copyright ramifications are explained AND AGREED TO by the buyer on the site per the coder's Seller Legal Agreement). ## Platform **Electro...

I need some drawings done in Solidworks. I know there are addon utilities to allow PCB layout packages like Orcad to be brought into Solidworks. The bottom line is that I have several metal boxes, brackets, and PCBs that are all parts of an assembly that I would like drawn in Solidworks. Please place your hourly rate and level of experience with Solidworks. There are so many parts that I can't list them as one project. But this is a starting point. ## Deliverables 1) Complete and fully-functional working program(s) in executable form as well as complete source code of all work done. 2) Installation package that will install the software (in ready-to-run condition) on the platform(s) specified in this bid request. 3) Complete ownership and distribution copyrights to all work ...