Design super cool high-tech headband
- Stato: Closed
- Premio: $250
- Proposte ricevute: 12
- Vincitore: cesarchacondi
Descrizione del concorso
Please look at the attached PDF for details on our project. We are looking for a skilled designer/engineer to create 3D renderings for our new product. Our product is a high-tech headband that will hold a transducer behind the ear. The headband -- these are not headphones -- will contain circuit board, batteries, led, switches and wires. This is a concept design that you are creating. Depending on your entries, we may hire you to do a final design for manufacturing.
We are standing by to answer any questions about the project.
Competenze consigliate
Feedback del Datore di Lavoro
“Cesar did a super design for us. He read our design brief and included all of the elements into his final work piece. His design was super!”
HomeLEDStore, United States.
Bacheca pubblica per chiarimenti
-
Titolare del Concorso - 6 anni fa
Designers -- We are busy going over each of the designs. The judges are very impressed with what they are seeing. We will be announcing the winner tomorrow...I hope. Again, thanks to everybody for submitting great designs. -- JDaggitt
- 6 anni fa
-
PrinceHooBa
- 6 anni fa
O we can not upload few shots ?!!
- 6 anni fa
-
CADTECH21
- 6 anni fa
#extended plz (24 hours)
- 6 anni fa
-
wshockley
- 6 anni fa
I need to know if you need a discreet design or a bold design.
- 6 anni fa
-
latheeshvmvilla
- 6 anni fa
Hi, pls give feedback on #10. Thanks
- 6 anni fa
-
cesarchacondi
- 6 anni fa
Dear Contest Holder Please rate my Entry, the #9
- 6 anni fa
-
CADTECH21
- 6 anni fa
Plz rate the Entry #8 and suggest changes if needed.
- 6 anni fa
-
kathire
- 6 anni fa
i am working it ,please wait for my entry.Thank you.
- 6 anni fa
-
cgblenderer
- 6 anni fa
Is this for 3D printing? Will you need the final model for 3D printing?
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Bishal -- The final product will be manufactured via injection mold. However, we will want to 3D print the device as a way to review it. - JTD
- 6 anni fa
-
cgblenderer
- 6 anni fa
Is someone not familiar with 3D printing not elligible?
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Designers -- A quick note of clarifications. There is only one transducer. And one circuit board. You can place the batteries on one side of the device and the transducer on the other side of the device. We like symmetrical designs, but all of the components do not need to be on one side. This should allow you to make the device smaller. -- JTD
- 6 anni fa
-
rajchoudhary265
- 6 anni fa
hiii are you there?
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Rakesh -- Yes, we are here. Hope you will consider submitting an entry for our contest. -- JTD
- 6 anni fa
-
CADTECH21
- 6 anni fa
HI , I am participating. I have very good idea for this challenge
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Manish -- Eager to see your entry. Thanks for considering our project. -- JTD
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
I like the entries 2 from Milos and 3 from Ahmed. The two designs look great. How do you see them fitting on the head? Do the headbands go around the back of the head? Over the top of the head? Or around the front of the head? Is there room for the batteries in these designs?
- 6 anni fa
-
PirkaStudio
- 6 anni fa
honestly I don't see people using something around the front of the head.
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Sebastian -- We think the two style that will work are typical headphones that go over the top of the head and a bone conduction style that goes around the back of the head. However, the ones that go behind the head need to place the transducer behind the head, yet remain firmly attached to the head. -- JTD
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
We are open to the style of headphone that Insight M posted. This is the shape of many bone conducting headphone. It is important to note that our transducer must be placed BEHIND the ear. The design used with bone conducting headphones would need to be modified to place the transducer behind the ear rather than in front of it.
- 6 anni fa
-
PirkaStudio
- 6 anni fa
Hi. A curious question. Every bone conduction headphone I know are placed in front of the ear. Its easier to fit cause you can grab also the ear. Why do you prefer to be placed behind?
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Sebastian -- For our device to work, the transducer has to be placed behind the ear. We are not building headphones, but a device for another purpose. The only way our device will work is if the transducer is behind the ear. That is the big design challenge. -- JTD
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Designers -- Do you prefer that the contest be "sealed" so that nobody can see your designs? I wasn't aware of this option until I had already posted the contest.
- 6 anni fa
-
PirkaStudio
- 6 anni fa
yes please.
you will also receive move diverse proposals. And its more serious.
#sealed please
thanks- 6 anni fa
-
cesarchacondi
- 6 anni fa
Hello. This it´s Very Cool Project. I'll be working in a proposal. I let you know if I have any doubt. Maybe you consider to #sealed
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Cesar -- Looking forward to you entry. We think it is a very cool product and are hoping to see some creative designs. -- JTD
- 6 anni fa
-
stefanache
- 6 anni fa
please post technical measuments for your product[s]
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Ion -- We posted a Design Brief as part of the contest. The Design Brief has all of the components and sizes as well as power requirements. We are giving you the flexibility to place the components within your design.
- 6 anni fa
-
PirkaStudio
- 6 anni fa
#sealed please
- 6 anni fa
-
Titolare del Concorso - 6 anni fa
Yes
- 6 anni fa
Come iniziare a usare i concorsi
-
Pubblica il tuo concorso Con facilità e in pochi istanti
-
Ottieni una Miriade di Proposte Da tutto il mondo
-
Seleziona la proposta migliore Scarica i file - Facile!