Find Jobs
Hire Freelancers

Arduino Code to activate RGB LEDs

$12-30 SGD

Chiuso
Pubblicato circa 5 anni fa

$12-30 SGD

Pagato al completamento
I want an Arduino with a sensor to drive some RGB LEDs. I have done a similar code before but I need more configurability. See requirement below... 1. Must run on ATTiny85. 2. Must be able to set number of RGB. 3. Must be able to choose RGB effects from "[login to view URL]" 4. Only ONE effect needs to be displayed. 5. RGB effects activated from a Microphone or Motion sensor. 6. Must be able to set Microphone or Motion sensor trigger threshold. 7. Must be able to set number of trigger for sensor. Please see attached for example of what I have done before.
Rif. progetto: 18954672

Info sul progetto

10 proposte
Progetto a distanza
Attivo 5 anni fa

Hai voglia di guadagnare un po'?

I vantaggi delle offerte su Freelancer

Imposta il tuo budget e le scadenze
Fatti pagare per il lavoro svolto
Delinea la tua proposta
La registrazione e le offerte sui lavori sono gratuite
10 freelance hanno fatto un'offerta media di $33 SGD
Avatar dell'utente
yes buddy, A super simple project to be done, u will get the best work accompanied with brotherhood,,,,,,,,,,,,,
$30 SGD in 1 giorno
4,7 (20 valutazioni)
3,8
3,8
Avatar dell'utente
hi sir I was so excited when i read ATTINY85, I want to take this work, I already work with the ATTINY85 and W2812 LEDs. I am an expert in automation and I study in a faculty of electronics.
$27 SGD in 10 giorni
5,0 (8 valutazioni)
3,4
3,4
Avatar dell'utente
Hi, I am kahan. I am embedded developer and have much experienced in hardware and software side. Waiting for further discussion. Thank you.
$46 SGD in 3 giorni
5,0 (6 valutazioni)
3,0
3,0
Avatar dell'utente
Hi, I could help with this project, I just would like to know if you want the microphone to be as a noise detection device ? Regards, Mohamed
$52 SGD in 1 giorno
5,0 (2 valutazioni)
2,7
2,7
Avatar dell'utente
I can write the code to drive the leds on Attiny85 as I have good experience with AVRs and arduinos
$26 SGD in 2 giorni
5,0 (1 valutazione)
0,6
0,6
Avatar dell'utente
I am new to this Freelancer site. However I have work experience of 4 year. I have worked on Arduino, and controllers of STM, NXP and Nordic semiconductor. So, I have great knowledge about programming and debugging code for controllers on Keil IDE or on Arduino. I have also worked on motion Sensors (Piezo, Gyro, Accelerometer, Magnetometer), IR sensors and designed many custom boards for a startup in India, Gujarat. I have just worked on a project that included RGBs. So, I know about the data sheets, current requirements, their different effects, calculations of resistor values of different RGBs and their manufacturers.
$27 SGD in 2 giorni
0,0 (0 valutazioni)
0,0
0,0
Avatar dell'utente
I will provide you all the firmware as per required flow I will provide bug free firmware . i will assist in testing . i will support till, end of project
$27 SGD in 2 giorni
0,0 (0 valutazioni)
0,0
0,0
Avatar dell'utente
hi. Ii just wanted to help you. I love doing Arduino projects specially rgb led. because the combination of the lights is really cool and amazing. I've done a lot of projects using rgb led. I'm sure i can help you a lot. hope you choose me. :). if you want to start now, just send me a message. :) . thanks. I'm just an electronics engineer who is passionate in doing things related to Arduino programming. :) thanks
$30 SGD in 1 giorno
0,0 (0 valutazioni)
0,0
0,0

Info sul cliente

Bandiera: SINGAPORE
SG, Singapore
5,0
1
Metodo di pagamento verificato
Membro dal feb 8, 2018

Verifica del cliente

Grazie! Ti abbiamo inviato tramite email il link per richiedere il tuo bonus gratuito.
Non è stato possibile inviarti l'email. Riprova per piacere.
di utenti registrati di lavori pubblicati
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Caricamento anteprima
Autorizzazione per la geolocalizzazione concessa.
La tua sessione è scaduta ed è stato effettuato il log out. Accedi nuovamente per piacere.