Completato

Electronic Circuits and Systems Analysis and LTspice

Analyze circuits and simulate through LTspice

More information in the PDF file included. There are also additional files which I will add when I award the project.

***Show every single step, work done, and explanation.
***LTspice MUST be used for the simulations
1)
For the four transistors shown, calculate the small-signal impedances indicated. If we compare
the result of (a) to (b), and (c) to (d), can we infer some approximate “reflection” rules that
describe how the BJT transforms impedances from one terminal to the other and vice-versa?

3)
Design (with hand calculations) the amplifier described above to have a phase margin of at least
60⁰ , while maximizing bandwidth. With an acceptable compensation capacitance, you should
have at least 100kHz 3dB bandwidth, but wider is better. ​Note that you will need some
information about the gain, output resistance, and capacitance of each stage in the amplifier to
perform these calculations. By simulating the amplifier in open loop, and using appropriate test
sources, you should be able to extract all of these parameters for the first and second stages.

Estimate the slew rate and large signal bandwidth for the amplifier given two inputs:
i) a -0.5V to +0.5V step input,
ii) a 0.5V​ peak​ sinusoid.
Make sure to include a schematic of your circuit, as you plan to implement in simulation and
measurement, as well as any relevant small-signal schematics you use for your analysis.

4)
Simulate the performance. You should simulate loop gain, phase margin, closed-loop
small-signal bandwidth, and the two large-signal inputs described in part 1. You may find that in
simulation the bandwidth must be decreased by further compensation. This would be observed in
either the phase margin of the small-signal performance, or as ringing with the step input. You
should adjust the compensation to maximize slew rate and bandwidth in simulation while
making sure that the step input settles without ringing. Include plots for these measurements, as
well as your testbench schematic

MAKE SURE TO LOOK AT PDF FILE TO SEE ALL INFORMATION

Competenze: Ingegneria Elettrica, Elettronica, Ingegneria, Ingegneria Meccanica

Vedere di più: linear circuits systems, swimming electronic touch systems, systems analysis design project, iadcs exam questions 2006 business systems analysis module, systems analysis website portal project design, object oriented systems analysis project proposal vbnet, electronic timing systems swimming, rajesh singh systems analysis, army materiel systems analysis activity resume, electronic timing systems cost, swimming races electronic timing systems, free systems analysis projects, systems analysis design hospital, higher diploma systems analysis nuig, business systems analysis design

Sul datore di lavoro:
( 12 valutazioni ) San Diego, United States

ID Progetto: #16741719

Assegnato a:

$20 USD in 1 giorno
(4 valutazioni)
0.0

7 freelance hanno fatto un'offerta media di $92 per questo lavoro

loi09dt1

A proposal has not yet been provided

$200 USD in 5 giorni
(101 Recensioni)
6.5
$25 USD in 1 giorno
(13 Recensioni)
4.5
thasleemreyasm

I have well experienced in doing such kind of jobs........................................and i will do my level best.............i will provide my previous LT spice work in private chat

$35 USD in 1 giorno
(3 Recensioni)
2.5
adilme

Hi. I am an electronic engineer and using LTspice for my on going projects such as designing filters using op amp and doing a.c. sweep analysts and finding cut off freq. I can do this and can you please provide more de Più

$88 USD in 5 giorni
(2 Recensioni)
2.6
$250 USD in 1 giorno
(4 Recensioni)
3.9
gncspm

A highly successful Electronics Engineering Professional with a proven track record of success in the installation, commissioning, testing and support of complex electronic installations across a wide range of marine, Più

$25 USD in 2 giorni
(0 Recensioni)
0.0