Ansyslavori
Cupping coil design for UAV using Ansys hfss or comsol
Wireless charging system for UAV, cupping coils :200w, litz awg40, operating frequency 100 kHz . In Ansys hfss or comsol
Design a wire less charging system for UAV . Cupping coil with AWG 40 , power 200w , frequency 100 kHz . In ansys hfss or comsol
Design a wireless charger in ansys hfss and the cupping coils with 100 kHz . litz wire AWG 40 . 200 w power.
I need someone having the ability to work on mechanical engineering academic assignments and having good knowledge of Mechanical Design and analysis. Following are the skills required 1. CAD (Solidworks, Siemens NX, Autodesk fusion) 2. FEA (Ansys) 3. CFD (Star ccm, Cfx) 4. Strong Knowledge of mechanical engineering concepts 5. Report writing and academic writing I'm looking for a long time relation. So if you have relevant skill and sincere in your work, We will be good together.
Its a tutoring task... I will need recorded screen for the tasks... Need to perform CFD analysis of an Axial Fan on a software package like ansys fluent, cfx.... For modeling geometery, BladeGen can be used or anyother suitable package.. Please BID and add step by step milestones payment... for example First milestone can be created for modeling geometery, seconde can be set for initial conditions and onwards... Pictures of existing fan are attached,,, NOTE: Desired out put is to calculate Outlet Pressure and Mass flow rate of an Axial Fan... and Compare experimental results with results of CFD analysis...
Looking for someone to model and analyse a column formwork in Ansys subjected to gradient pressure and dynamic pressure from wet concrete.
I will provide the research paper for the reference study and define the environment in which I need my work
I want to extract data from a fluent simulation. I want to obtain the data from a fluent simulation I made for all the timesteps. Right now I am unable to obtain the data for only one timestep. I need an ANSYS fluent consultant who will help me to extract the data for every timestep.
ANSYS software specialist is needed for the development and location of pelton turbine blades
ANSYS software specialist is needed for the development and location of pelton turbine blades
1. Mesh In ICEM for 4 model 2. Set-up model in k-epsilon and in RMS 3. Run simulation for mesh indipendent study 4. rest of simulation run with fine mesh 5. save all data and results 6. need save individually for clear information in attach file.
Hello, I need someone to make a design for me in fluent ansys (I already have all the dimensions and the design) then make fluid and thermal analysis for it including finding; mesh, velocity vector and 4 figures (I will mention them once we agree)
Al Majeed Academy It may have the following sections: a. On Line Quran teaching classes. b. Islamic research centre. c. A library consisting of reference books and a vast e liberary. d. Short and long quran learning and translation courses for women. e. Lectures from different Islamic scholars on selected topics. f. Courses for Autocad, Solidworks, Ansys, Hysys, Matlab etc.
Hi Alexandre D., I noticed your profile and would...Alexandre D., I noticed your profile and would like to offer you my project. We can discuss any details over dear. I am happy reading your message. And the offer you made. search title: Design and Optimal Control of lower-limb Wearable Exoskeletons Robot for Gait Rehabilitation after Spinal Cord Injury. 1- Mechanical design with 6 DOF by solidworks software. 2- Analyzing stresses by ansys software. 3- A dynamic simulation and kinematic by simwise software. 4- Optimal control design by matlabsimulink software. 5- Manufacturing the robot .,, Real dimension. Please study the project and send me detailed costs with the time period for each point. I hope we can agree to complete the project. Greetings to you with many thanks ..
I have the geometry of three blades in solidworks I need a person who analyzes the jet of water on these blades in a static way, analysis of the jet speed and force and torque produced in the blade is needed,analysis is required on ansys CFX
1. Eliminate error "Update-Dynamic-Mesh failed. Negative cell volume detected" in Fluent (Maybe setting error or mesh error) 2. Compile my UDF after fix the Error 3. run the Fluent with UDF code at least 3-5 hrs no error.
i need design and control by Mechanical Engineering .. Solidworks .. 3D Modelling and check by ansys ..with make simulation design,Stress analysis, kinematic simulation, control design,manufacturing.
I would like to hire an experienced CFD simulation engineer to provide some advice with an analysis I am performing for an air purifying system in ANSYS Fluent. The ideal candidate must be an expert in running radiation simulations using the DO radiation model and skillful with lagrangian particle tracing. The system is extremely simple with 2 UV lamps in line with the flow as shown in the pictures attached. In the end, the simulation should provide an estimation of the total UV dose in J/m2 using the particles as probes (see attached picture). The candidate should have fluent installed in their PC for demo purposes, the PC i use to run the simulations is isolated from the rest of my company's network so there is no way for me to share my desktop or anything similar. I will pro...
...(pump/coupling/motor/base) relative to suction and discharge nozzle centerlines. • FEA reports of the linear analysis of 08 nos. pump base frames having plots for induced stress and deflection. Note: The FEA will be based on the equipment total static weight and application of allowable nozzle loads as per ANSI/HI 9.6.2-2015 for class 125 cast iron flanges. Software to be Used: SolidWorks 2018, Ansys Assumption: It is assumed that on a need basis, appropriate instructions, standards, working methods, and other necessary information related to the project will be provided. Proposed Execution: • Study the scope intent and input data provided by client. • Create the first base frame design in 3D as per the design intent. • Carry out the checking of 3D models...
I am looking for Ansys Maxwell expert who can design a spiral cupping coils for both transmitter and receiver. Specification to design coils: Air gap between coils : 0-150mm Lateral displacement of coils: 0-50mm (diameter of coils between 0mm to 50 mm) in put transmitter Power: 200W I want results the power must transfer to UAV at least 70% of power at receiver,
design a spiral cupping coils for both transmitter and receiver using ferrite base for unmanned Arial vehicle using Ansys Maxwell software.
I wrote my Ansys Fluent UDF . I need to fix it .
Hi, I need ICE-Fluent expert using ansys 19.2 or above. You must know the knowledge about the ice-fluent (not fluent flow). So kindly apply if you have past experience of ice-fluent. Also you will be needing to show my past experience or work regarding ICE-Fluent. I need the work done in 2 days Please write ICE-fluent on the top of bid so I can consider you. Kind regards
I want to design a 130 watt BLDC motor with high efficiency. All the design parameters should meet manufacturing measures. At least simulation results should be appropriate. Here I am attaching a reference document but its for only reference to dimensions. FEA of the motor is also required.
I need to perform a Conjugate heat transfer analysis of thermoelectric cooler that have two heat sinks on the hot and cold side with 4 different currents applied to the device and see the temperature distribution inside the device (conduction) and also outside the device in the two flow channels(each one for both sides) for convection HT. the following need to be done: 1) You will design the CAD of the device and,heat sinks and the channels with a given dimensions. 2)Perform a CFD simulation for a Non-pulsating air flow for both channels and at a given inlet velocity for the 4 different currents(4,5,6,7)A 3)Perform a CFD simulation for Pulsating air flow (sin wave pulse) for the 4 currents mentioned above. At each current, the angular frequency of the pulse(omega) will vary for 4 values (...
I am looking for Ansys Maxwell expert who can design a spiral cupping coils for both transmitter and receiver. Specification to design coils: Air gap between coils : 0-150mm Lateral displacement of coils: 0-50mm (diameter of coils between 0mm to 50 mm) in put transmitter Power: 200W I want results the power must transfer to UAV at least 70% of power at receiver,
design a spiral cupping coils for both transmitter and receiver using ferrite base for unmanned Arial vehicle using Ansys Maxwell software.
I need ansys expert 19.2 or newer version who can easily work for ICE-fluent module. I have piston need to do velicity vector analysis on it. Everything is done, geometry, meshing, boundary conditions, I just need you to do the analysis. I will send you the 3d geometry. Also write “ICE-Fleunt” on the top of your bid so I can consider you, otherwise I will not respond you.
Hi there, I want someone to perform a fatigue analysis on a stepped shaft with and without a fillet. I have uploaded a image for reference. These are points which you have to keep in mind while designing 1. Select your choice and dimension and torque for the model. 2. Assume suitable materials property. The whole shaft can be made of one material or you can assume two different materials. 3. Assume a torsional load on shaft. 4. Setup a FE model and analyse it. 5. First perform a fatigue analysis on the stepped shaft with no fillet at B. 6. Create a fillet a B and perform fatigue analysis. 7. Compare the influence of the fillet radius on the Factor of Safety and Fatigue life sensitivity. 8. You may use fully reversed loading condition. 9. Compare the FoS using different fatigue failure Cr...
i need an industrial tutor to learn ansys fea,cfd, etc
design a spiral cupping coils for both transmitter and receiver using ferrite base for unmanned Arial vehicle using software called Ansys Maxwell software. the receiver is smaller than the transmitter. and design with using given parameters. and transmitter transfer the power 200w . Specification to design coils: Air gap between coils : 0-150mm Lateral displacement of coils: 0-50mm (diameter of coils between 0mm to 50 mm) in put transmitter Power: 200W I want results the power must transfer to UAV at least 70% of power at receiver, 0)type of litz wire used 1)no of turns both transmitter and receiver , 2) distance between 2 coils , 3) internal diameter and external diameter of both coils , 4)impedance value , 5)capacitance value , 6) displacement of both coils , 7)magneti...
design a spiral cupping coils for both transmitter and receiver for unmanned Arial vehicle using software called comsol multilayer or Ansys Maxwell software's. the receiver is smaller than the transmitter. and design with using specific parameters. and transmitter transfer the power 200w . I want results the power must transfer to UAV at least 70% of power at receiver. Specification: Air gap between coils : 0-150mm Lateral displacement of coils: 0-50mm (diameter of coils between 0mm to 50 mm) in put transmitter Power: 200W
Description of the project: This project is to evaluate and design a test stand for use in the closed wind tunnel to investigate the interaction between the rocket engine plume and the external aerodynamics of a launch project build upon a previous project will focus on the design of a new test stand and contuct computational work to model the test environment.
Me gustaría un videocurso de varias clases (varios vídeos) que tratara sobre una guía completa a Ansys Fluent para realizar CFD, es decir cómo simular distintos casos y explicando al detalle las herramientas de cada módulo de Fluent y cómo afectan. La duración mínima en total sumando todos los vídeos 3 horas. Idioma español.
Hi Asad S., I noticed your profile and would like to offer you and chat with you i am mechanical engineer with experience in solidworks and ansys if you gave to work with you. We can discuss any details over chat.
i need someone who could do dynamic mesh and solve in multiphase water/air using ansys as well as y+ .. dont bid if you cant do it must show sample that you can ..
Electromagnetic Design of PMSM, with the following point to understand and Carter's coefficient 1. Developing an excel file for analytic design. 2. Developing a MATLAB mfile for auto-generation of vbs script for generation of designs in ANSYS maxwell software (This code couples excel file to Maxwell software). 3. Calculation of magnetic loading (Determination of proper magnet arc). 4. Magnet sizing (By FEA & ANSYS Maxwell optimization solvers). 5. Demagnetization study (Determination of proper magnet depth). 6. Calculation of armature field. 7. Calculation of static torque (Tout versus dq currents). 8. Calculation of back EMFs and cogging torque. 9. Steady state simulation of motor. 10. 3D skew study for reduction of torque ripple.
I have ANSYS APDL script. Only use in MATLAB Like this video
Help in Flow Analysis around an airfoil WITH ANSYS 2020 R1 ( With CFX)
i need someone to design a cooking pan then place it on a heat source and simulate how long it will take to reach 100 celsius materials should be taken into hand technical report should be written as well as steps done Ansys is a must
...ourselves just materials other than the ones we will initially designate. The outputs we are primarily focused on are: % compression, contact stress, force applied within the elastic region (a graphical output of the linear-plasto shift), if you have the ability to determine if a seal has been created that is just a bonus. We would like the simulation to be done in Nastran Inventor, Fusion 360, or ANSYS, we are willing to download other software as well if you have a strong recommendation for software you believe to be the best for the job. You will also be asked to sign an NDA. We project that a skilled individual should be able to complete this simulation in less than one hour as the design is already complete. The perfect candidate would be able to: complete the task,...
...structure to design the membrane, u can refer the senior report Chapter 4 result and discussion : submit before 1/9/2020 -use AHSYS fluent to simulate the hydrodynamic profile and and get the result Chapter 5 : Same as chapter 4, 1/9/2020 *My report need matlab to design a tpms structure and put it into autocad or solidwork to generate the shape of tpms mixed matrix membrane. Then simulate in ansys fluent to check the hydrodynamic profile and other result....
Me gustaría un videocurso de varias clases (varios vídeos) que tratara sobre una guía completa a Ansys Fluent para realizar CFD, es decir cómo simular distintos casos y explicando al detalle las herramientas de cada módulo de Fluent y cómo afectan. La duración mínima en total sumando todos los vídeos 3 horas. Idioma español.
Hi, I need to see exact airlfow visualization simulation of how the air comes out the attached HVAC Diffuser, it is a .step file of a 10 inch diffuser, and then trace the airflow as it goes through a room. We already have a version from Catia5 using ANSYS but not working correctly, ask me to see image, could not attach here. The ideal person will have the SolidWorks HVAC Module I need this diffuser mounted 2 feet down from the ceiling and need to see the airflow that comes out of the diffuser and how the air flows throughout a room. I also need the airflow to go through the attached diffuser in a realistic manner. We are designing a new type of patented HVAC system to help clean air faster to deal with COVD19 virus in indoor
I will provide dimensions of wing and airfoil used and i need a complete cfd study using ansys to determine full profile, in the end provide a full report of all technical data gathered from cfd
Hi, Looking for someone, who has expertise in ANSYS, MATLAB, SOLIDWORKS, CFX/FLUENT or equivalent. We need to design backed up with simulation software results, CFD results, FEA results. Freelancer must have expertise in mechanical and aerospace designing. Thank You
Hello, I have the following task for my bachelor thesis: I have a 3D image (i can share it with you) which i put in Ansys spaceclaim, i took manual a 10 by 10 mm section (cube) of this 3D image in Spaceclaim, and i have recorded the Python code of it. what i exactly need that you parameterize this code, so that i can use it on this 3D image and only change the coordinates to get any new sections which i want. are you able to do this ? If you need any other informations please write to me thanks
Hello, I have the following task for my bachelor thesis: I have a 3D image (i can share it with you) which i put in Ansys spaceclaim, i took manual a 10 by 10 mm section (cube) of this 3D image in Spaceclaim, and i have recorded the Python code of it. what i exactly need that you parameterize this code, so that i can use it on this 3D image and only change the coordinates to get any new sections which i want. are you able to do this ? If you need any other informations please write to me thanks